Fabricator TIG welding a turbo manifold at Cain's Chassis in Adel, Georgia

Adel, Georgia · Custom Fabrication Shop

Chassis Fab.
Wiring.
No Shortcuts. Custom chassis fabrication, automotive wiring & full custom builds in Adel, GA

Ground-up chassis work, hand-built wiring harnesses, and engine swaps that hold up under load — on classics, street cars, trucks, and trail rigs across South Georgia.

See The Work Start A Build

In The Shop Now

SEMA 2026:
Raptor XL

Our F-250 "Raptor XL" is headed for the SEMA show floor — full custom chassis and suspension work, a complete one-off wiring harness, and a custom-ordered wheel package to match.

The rendering is all we're showing until the truck is revealed at SEMA this November. Build photos follow after the show.

Follow The Build

Concept rendering of the Raptor XL, a custom Ford F-250 built by Cain's Chassis for the SEMA show, shown in white with gold wheels and a custom front bumper — Concept rendering · Full reveal at SEMA 2026

Featured Build

F-150 Raptor · Gold Beadlocks

White Ford F-150 Raptor on custom gold beadlock wheels

Clean, aggressive, and built to be driven. This Raptor runs a custom-ordered black-and-gold beadlock package, spec'd and fitted to sit right under a truck that still has to work like a truck.

Wheels Custom-ordered beadlock package
Stance Suspension setup & fitment
Electrical Accessory wiring, done clean

Build Yours

Custom-ordered beadlocks

What We Do

Chassis, Wiring & Custom Build Services

The work most shops send out, we do here in Adel — frame, wire, motor, finish.

Custom Chassis Fabrication

Custom frames, suspension setups, crossmembers, and structural work built to spec — measured, jigged, and welded right.

Automotive Wiring Harnesses

Complete custom harnesses, clean routing, proper loom and terminations. Electrical that survives heat, vibration, and years of use.

Engine Swaps & Drivetrain

LS, Coyote, and Hemi swaps, turbo and supercharger setups, driveline and rear-end work for street or strip.

Custom Wheels & Fitment

Custom wheel and tire packages ordered to suit the build, then fitted for the right offset, clearance and stance.

Classic Truck Restoration

Ford pickups and muscle brought back from patina to show-ready — body, interior, glass, and everything underneath.

Full Custom Builds

Bring the idea and the vehicle. We handle fab, wiring, assembly, and tuning from bare frame to keys in hand.

The Work

Custom Builds Out Of This Shop

Chassis fab, wiring, engine work and finished rigs. Click any photo to open it full size.

F-150 Raptor on custom beadlocks

Bare custom chassis with front suspension installed during a ground-up build — Ground-up chassis build

Twin-turbo LS engine bay with polished intake piping in an orange car — Twin-turbo LS

Finished black Chevrolet Camaro on bronze wheels — Camaro, out the door

Custom automotive wiring harness routed and loomed along a frame rail — Hand-routed harness work

Blue Nissan Skyline GT-R R33 on a two-post lift in the shop — Skyline GT-R on the lift

Patina Ford F-100 pickup with an LS engine swap in progress — Patina F-100, LS-swapped

Custom red and black beadlock wheel — Custom beadlock package

Magnuson supercharger installed on a truck engine — Supercharger install

White Jeep Wrangler Rubicon on red beadlock wheels and off-road tires — Rubicon, trail-built

Custom fabricated stainless steel headers on a workbench — Custom header fab

Finished red 1956 Ford F-100 pickup with whitewall tires — 1956 F-100, done right

Supercharged Hemi engine build with polished intake — Supercharged Hemi

Custom red battery cables routed through a frame bracket with grommets — Clean electrical, every time

Red high-amperage cable secured along a powder-coated frame rail — Cable routing & support

Custom wood steering wheel and digital gauge cluster in a 1956 Ford F-100 — Custom interior, '56 F-100

Chassis rail with front suspension components being fabricated — Suspension & chassis fab

Ford Coyote 5.0 engine swap with cold air intake in a classic truck — Coyote swap

Restored Ford F-100 tailgate with red lettering and polished chrome bumper — Restoration detail work

Custom dual exhaust and undercarriage fabrication viewed from below — Underside fab & exhaust

Replacement floor pan and rocker panel fabrication on a muscle car shell — Floor pan & body fab

Close-up TIG weld bead on a stainless steel exhaust flange — Weld quality, up close

Black and gold custom beadlock wheel with machined lip — Black & gold beadlocks

How It Goes

From Idea To Keys In Hand

Talk It Through

Call or bring the vehicle by. We go over what you want, what it'll take, and what it's honestly going to cost.

Fab & Fit

Chassis, suspension, mounts, and exhaust get fabricated and fitted to the vehicle — not forced to fit.

Wire & Assemble

Harness built and routed by hand, drivetrain in, systems hooked up and checked before anything gets buttoned up.

Sort & Deliver

Shake it down, sort the details, and hand it back running the way it should — with nothing left on the to-do list.

Hand-fabricated stainless headers in front of a patina Ford project truck

253 Tunison Road · Adel, GA

Built By Hand.
Backed By Standards.

Cain's Chassis & Automotive Wiring is a South Georgia shop doing the work most places sub out — chassis fabrication, custom wiring, engine swaps, and full custom vehicle builds, all in house.

Patina Ford pickup, twin-turbo street car, trail rig, or a truck headed to SEMA: it gets built to run right and last, not just look good sitting still. We take work from Adel, Valdosta, Tifton, Moultrie, Nashville and across South Georgia.

In-HouseFab, wiring & assembly

Show-LevelFinish & detail work

Straight TalkHonest scope & pricing

Questions

Common Questions

What kinds of vehicles do you work on?

Classic Ford pickups, muscle cars, late-model trucks, imports and trail rigs. If it needs a frame built, a harness wired, or a motor swapped, it belongs in the shop.

Do you build custom wiring harnesses from scratch?

Yes. We build complete custom harnesses by hand, route and loom them properly, and terminate every connection so the electrical survives heat, vibration and years of use.

Do you do engine swaps?

We handle LS, Coyote and Hemi swaps along with turbo and supercharger setups, custom mounts, headers, exhaust, and the wiring that has to come with it.

Can you build a vehicle from a bare frame?

Yes. Full custom builds are handled in house from bare frame through fabrication, wiring, drivetrain and final assembly.

Where are you located and what areas do you serve?

The shop is at 253 Tunison Road in Adel, Georgia. We regularly take work from across South Georgia including Valdosta, Tifton, Moultrie and Nashville, and we take out-of-town builds as well.

How do I get a quote on a build?

Call the shop at 229-237-3347 or stop by. We go over what you want, what it'll take, and what it's honestly going to cost before any work starts.

Have a build in mind?

Chassis fab, wiring, engine work, or a full build from scratch — bring it to the shop.

Call 229-237-3347

Open Monday – Friday · 8:00 AM – 5:00 PM

Chassis Fab.Wiring.No Shortcuts. Custom chassis fabrication, automotive wiring & full custom builds in Adel, GA

SEMA 2026:Raptor XL